Know-how & tips

Diesel as a release agent in asphalt construction: What laboratory measurements reveal

Reviewed by Eco-Nova GmbH · Last updated 7 October 2026 · 4 mins’ read time

A tipper lorry tips a load of asphalt mix into the road paver

Key points at a glance

Diesel is problematic as a release agent: amongst other things, it is classified as flammable, harmful to health and hazardous to water; it dissolves bitumen and significantly increases vapour and aerosol levels. In laboratory tests carried out by TPA GmbH, the measured value with diesel was around five times higher than without a release agent. With the rapeseed oil-based Antistick ECO, it was 74 to 80 % lower than with diesel.

Key messages

  • In laboratory tests (TPA, IFA method, SMA 8 S, 150 °C), diesel produced 543.5 mg/m³ of fumes and aerosols, approximately five times the level produced by the mixture without a release agent.
  • With Antistick ECO, the figures ranged from 105.9 to 141.1 mg/m³, which is 74 to 80 % lower than diesel.
  • Diesel is flammable, harmful to health, hazardous to water (WGK 2) and classified as a dangerous good under ADR.
  • BG BAU advises against the use of release agents containing mineral oil; from 2027, the limit value for bitumen vapours will also apply to rolled asphalt.

Contents

On many construction sites, diesel is still sprayed onto skips, rollers and tools as a release agent. It is cheap and readily available. However, diesel is problematic as a release agent: for health, for soil and water, for the mix – and for the measurement values that will also count for rolled asphalt from 2027 onwards. A laboratory measurement now shows just how big the difference is.

The disadvantages of diesel as a release agent

  • Health: Under the CLP Regulation, diesel is classified, amongst other things, as flammable, harmful if inhaled, a skin irritant and suspected of causing cancer. When sprayed onto hot surfaces, workers inhale vapours and mist.
  • More vapours and aerosols: In laboratory tests, the measured value for diesel was approximately five times higher than that for the mixture without a release agent. BG BAU therefore advises against the use of mineral oil-based release agents in its industry-specific solution for rolled asphalt.
  • Fire hazard: The flash point of diesel is 55 °C and above, which is well below the temperature of hot tarmac and hot machine parts.
  • Soil and water: Diesel is highly hazardous to water (WGK 2) and toxic to aquatic organisms. Any diesel that drips from the trough, roller or tool ends up in the ground or in the sewer system.
  • Mixture: Diesel dissolves bitumen. If it drips onto the mix or into the trough, it can soften the binder in places.
  • Transport and storage: Diesel is classified as a dangerous good under the ADR and must be transported and stored accordingly.

Laboratory test: Diesel versus Antistick ECO

TPA GmbH (Labor Hamburg) carried out measurements on behalf of Eco-Nova to determine the extent to which release agents affect the vapours and aerosols from hot asphalt mix. The study was based on the method developed by the DGUV Institute for Occupational Safety and Health (IFA Workbook 6305, Method 1). A SMA 8 S chip-sealer was agitated at 150 °C in a laboratory mixer, whilst the air above it was extracted through a glass fibre filter (aerosols) and an XAD-2 cartridge (vapours). The samples were analysed by the ANECO Institute for Occupational Safety and Health.

SMA 8 S mix, 150 °C Total measured value for vapours and aerosols compared with diesel
without release agent (reference) 104.0 mg/m³ –81 %
with Antistick ECO 150 LV 105.9 mg/m³ –80 %
with Antistick ECO 150 120.6 mg/m³ –78 %
with Antistick ECO 170 141.1 mg/m³ –74 %
with diesel 543.5 mg/m³ –

The result: With diesel, the total measured value was 543.5 mg/m³ – around five times higher than without a release agent. With Antistick ECO, the values were 74 to 80 % lower. Antistick ECO 150 LV, at 105.9 mg/m³, was almost on a par with the mixture without a release agent.

Work on a building site is never carried out entirely without a release agent. It is therefore crucial to compare it with what is normally used – and there is a world of difference between diesel and Antistick ECO.

Laboratory test results, one measurement per variant. These show the effect of the release agent in a direct comparison and cannot be compared with measurements taken on site or with the workplace exposure limit; in those contexts, the values are significantly lower. Whether the limit value is complied with at an installation site depends primarily on the installation temperature, extraction and working methods. We will send you the full test report on request: Request a test report.

A comparison of Diesel and Antistick ECO

Diesel Antistick ECO 150 / 150 LV / 170
Laboratory measurement of vapours and aerosols* 543.5 mg/m³ 105.9 to 141.1 mg/m³ (74–80 % less)
Classification including: flammable, harmful if inhaled, suspected of causing cancer, toxic to aquatic organisms Not classified as hazardous according to the safety data sheet
Flash point from 55 °C above 150 °C (ECO 170: above 170 °C)
Transport Dangerous goods in accordance with ADR (Class 3) Not classified as a dangerous good under ADR
Water hazard class WGK 2 (significantly hazardous to water) WGK 1 (self-assessment)
Raw material base Mineral oil plant-based raw materials (rapeseed oil methyl ester)
Effect on bitumen dissolves bitumen designed for use as a release agent

* Laboratory test carried out by TPA GmbH in accordance with IFA Workbook 6305, Method 1, SMA 8 S at 150 °C (test report dated 6 October 2026). Information on Antistick ECO as per the safety data sheet; information on diesel as per the GESTIS substance database.

Which ECO anti-stick coating is suitable?

  • Antistick ECO 150: the standard for most applications in asphalt construction.
  • Antistick ECO 150 LV: for automatic spray systems with fine nozzles; in laboratory tests, it recorded the lowest reading in the series.
  • Antistick ECO 170: thicker consistency, suitable for long transport distances, PmB and multiple loadings.

Switching from diesel in four steps

  1. Do not top up the diesel and do not mix Antistick ECO with diesel.
  2. Flush the tank, pipes and nozzles, for example, using Bituclean Extra.
  3. Insert the test sample: 10 or 20 litres using your own machinery and your own mix.
  4. Planning the season: Delivery in drums or IBCs, tailored to your requirements.

Request a sample or a quote – or read more about the limit value: AGW bitumen from 2027: What asphalt contractors need to bear in mind regarding release agents.

This article provides an overview and is not a substitute for legal advice or a risk assessment. Last updated: October 2026.

Advice on release agents

The right release agent for your machines

Just let us know which machines you have, your spraying system and your annual requirements – we’ll recommend the right Antistick ECO product and draw up a quotation. Test quantities of 10 or 20 litres are available.

Would you prefer to speak on the phone? +49 5923 9936-25

FAQ

Frequently Asked Questions

Can diesel be used as a release agent?
Diesel is a cause for concern as a release agent. In its sector-specific guidelines on rolled asphalt, BG BAU advises against the use of release agents containing mineral oil, as they increase the measured levels of bitumen vapours. From 1 January 2027, the occupational exposure limit will also apply to rolled asphalt.
How much more fumes and aerosols are produced by diesel?
In the laboratory test carried out by TPA GmbH, the total measured value was 543.5 mg/m³ with diesel, 104.0 mg/m³ without a release agent, and between 105.9 and 141.1 mg/m³ with Antistick ECO. Laboratory results are not comparable with on-site measurements.
What is the alternative to diesel?
A release agent free from substances containing mineral oil, such as Antistick ECO, which is based on rapeseed oil methyl ester. According to the safety data sheet, it is not classified as hazardous, is not classified as dangerous goods under ADR, and has a flash point above 150 °C.
How do I switch from diesel to Antistick ECO?
Do not top up with diesel or mix it with other fuels; flush the tank, pipes and nozzles, and then use a test quantity of 10 or 20 litres in your own machinery.

Suitable release agents

These products help

A version of Antistick ECO 150 for automatic spraying systems fitted with fine nozzles on pavers and rollers.
Universal release agent based on plant-derived raw materials (rapeseed oil methyl ester) for pavers, rollers, troughs and hand tools used in asphalt construction.
A viscous release agent based on plant-derived raw materials (rapeseed oil methyl ester) with a flash point above 170 °C – provides exceptionally long-lasting adhesion.

Are you planning for the next tarring season?

We can advise you on switching to Antistick ECO and provide you with a quote tailored to your annual requirements.

Read more

More from ‘Knowledge & Tips’

Stainless steel tank with pipework in a production plant
16 October 2026
· Know-how & tips

CIP cleaning: procedure, cleaning agents and the correct parameters

CIP (Cleaning in Place) involves cleaning tanks, pipework and plant without dismantling them. Cleaning solutions are circulated through the system. Typical steps include pre-rinsing and alkaline cleaning to remove…

Read more →
Cleaning mixing vessel
13 October 2026
· Know-how & tips

Cleaning in the masterbatch and plastics industry: colour changes, caking, residues

In masterbatch production and plastics processing, cleaning is a key factor in determining colour change times, scrap rates and product quality. Residual pigments and additives, cracking at high temperatures and colour carry-over are the typical problems. Cleaning pellets help…

Read more →
Offshore wind farm with an installation vessel in the North Sea
5 October 2026
· Know-how & tips

Removing salts before coating: the Bresle test, limit values and procedure

Salts such as chlorides and sulphates are trapped in the rust scars of corroded steel and, when a new coating is applied, cause blistering and corrosion. The salt content is measured using the…

Read more →