Rapeseed oil-based release agent

Antistick ECO 150

Universal release agent based on plant-derived raw materials (rapeseed oil methyl ester) for pavers, rollers, troughs and hand tools used in asphalt construction.
Antistick ECO 150 in a 1,000-litre IBC

Item No. 0770

At a glance

This is what the release agent does

Prevents bitumen and asphalt from sticking; adheres to surfaces for a long time and can also be used at higher temperatures. Not classified as hazardous according to the safety data sheet; not classified as a dangerous good under ADR; flash point above 150 °C.

Raw material base

plant-based raw materials (rapeseed oil methyl ester)

Classification

Not classified as hazardous according to the safety data sheet

Flash point

above 150 °C

Container

10, 20, 60, 200, 1.000 L

Laboratory test

Antistick ECO: significantly fewer fumes and aerosols than with diesel

In the laboratory test carried out by TPA GmbH, the measured value was Antistick ECO 150 at 120.6 mg/m³ – around 78 % below the level recorded with diesel (543.5 mg/m³). Diesel therefore resulted in a level 4.5 times higher than that of Antistick ECO 150.

In the laboratory test carried out by TPA GmbH, the measured value was Antistick ECO 150 LV at 105.9 mg/m³ – around 80 % below the figure for diesel (543.5 mg/m³). Diesel therefore resulted in a reading more than five times higher than that of Antistick ECO 150 LV. Without a release agent, the reading was 104.0 mg/m³ – ECO 150 LV is almost at this level.

In the laboratory test carried out by TPA GmbH, the measured value was Antistick ECO 170 at 141.1 mg/m³ – around 74 % below the level recorded with diesel (543.5 mg/m³). Diesel therefore resulted in a level almost four times higher than that of Antistick ECO 170.

Without release agent (reference) · 104.0 mg/m³

Antistick ECO 150 LV · 105.9 mg/m³

Antistick ECO 150 · 120.6 mg/m³

Antistick ECO 170 · 141.1 mg/m³

Diesel · 543.5 mg/m³

Work on a building site is never carried out entirely without a release agent. It is therefore crucial to compare this with a substance that is still frequently used: diesel. Diesel is a mineral oil product, and BG BAU advises against the use of release agents containing mineral oil.

Test report by TPA GmbH, Hamburg Laboratory, dated 6 October 2026: Measurements carried out in accordance with IFA Workbook 6305, Method 1, using SMA 8 S mastic asphalt at 150 °C; one measurement per variant; analysis carried out by the ANECO Institute for Occupational Safety. The laboratory results demonstrate the influence of the release agent in a direct comparison. They are not comparable with measurements taken on site or with the workplace exposure limit; in those contexts, the values are significantly lower. We will send you the full test report on request.

Deployment

Suitable for

  • Road pavers: screed, auger, tamper
  • Tandem and rubber-tyred rollers
  • Transport and insulated containers
  • Asphalt boiler
  • Hand tools such as shovels, rakes and trowels
  • Moulds and formwork

Processing

  • Use pure
  • Clean surfaces beforehand, e.g. with Bituclean Extra
  • Spray lightly and do not use too much: a continuous, as thin a layer as possible provides the best protection
  • Do not mix with hydrocarbon-based release agents
  • Before the changeover, use up any remaining stock and flush the system
  • Test for material compatibility beforehand

Technical Specifications

Data as per the data sheet

Information as per the safety data sheet and technical data sheet. The most recent data sheet shall prevail.

Anti-Stick ECO

A comparison of the series

All three release agents are based on plant-derived raw materials (rapeseed oil methyl ester) and, according to the safety data sheet, are not classified as hazardous. They differ in terms of viscosity and their primary applications.

Antistick ECO 150 in a 1,000-litre IBC

Antistick ECO 150

The standard for most applications in asphalt construction

Antistick ECO 150 LV in a 1,000-litre IBC

Antistick ECO 150 LV

For automatic spray systems with fine nozzles

Antistick ECO 170 in a 1,000-litre IBC

Antistick ECO 170

Thicker – for long-lasting adhesion and high temperatures

Documents

Documents relating to procurement and health and safety

We would be happy to send you the technical data sheet and tender documentation. The safety data sheet is provided to existing customers and prospective customers who receive a sample or a demonstration – please request this using the form.

FAQ

Frequently Asked Questions

In most asphalt construction applications, yes. Use up the remaining stock, flush the plant and carry out a preliminary test using a sample quantity of 10 or 20 litres. Do not mix the two release agents.
For automatic spray systems with fine nozzles and fine-mesh filters on pavers and rollers. ECO 150 LV has the same raw material composition and classification as ECO 150.
Store Antistick ECO 150 in a frost-free place at a temperature between 5 and 30 °C. It may thicken if exposed to frost; once warmed up, it is ready for use again.
Available in 10, 20 and 60-litre containers, 200-litre drums and 1,000-litre IBCs. We’ll be happy to provide a quote on request, tailored to your annual requirements.

Enquiry

Request a quote or a sample

Please let us know the product, your approximate annual requirement, the packaging size and the delivery address. We will provide you with a quote tailored to your quantity. Sample quantities of 10 or 20 litres are available.

Mareen Portheine, Sales and Technical Advice on Release Agents at Eco-Nova

Mareen Portheine

Sales & Technical Support · German, Dutch, English

Saskia Wolbers, Internal Sales and Back Office at Eco-Nova

Saskia Wolbers

In-house Sales & Back Office · German, Dutch, English

1Your requirements
2Contact details
Your enquiry
Non-binding – we will provide you with prices in our quotation.
Product
Container
A rough estimate will do, e.g. 2,000 litres.